Showing results: 256 - 270 of 361 items found.
-
40-570-415 -
Pickering Interfaces Ltd.
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
40-570-111 -
Pickering Interfaces Ltd.
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
40-570-214 -
Pickering Interfaces Ltd.
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Bloomy Controls, Inc.
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
Cincinnati Sub-Zero Products
CSZ's accelerated stress test chambers combine mechanical refrigeration; LN2 cooling and high velocity air flow for fast product temperature change rates. Chambers are typically designed with a change rate up to 30C (54F) per minute based upon the part temperature. Common uses are production stress testing circuit boards, electronic drives, assemblies, etc. Design allows the user to quickly control and change the temperature of the product.
-
Dayton T. Brown, Inc.
Dayton T. Brown, Inc. can help ensure that your payload is delivered accurately and reliably every time. Our team is responsible for first article, production lot, qualification, and associated testing and engineering support for mechanical and electrical armament and missile launching systems. DTB can help you develop a customized test plan that combines testing across many specifications – environmental, dynamics, EMI/EMC, structural, and non-destructive. Some of the standards that we follow include:
-
ExpressBox 3400 -
Wuntronic GmbH
Magma's ExpressBox 3400 is the latest PCIe expansion chassis in our growing Gen 3 product line. Featuring (7) PCIe slots, x8 electrical and x16 mechanical, the EB3400 is ideal not only for high performance I / O PCIe cards, but is perfect for super fast SSD and computational GPUs. Known for reliability, Magma designed this chassis with the extremes of simulation, test and measurement, and high performance computing in mind. The EB3400 is highly adaptable and
-
Nanovea Inc.
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
Washington Laboratories LTD.
There are several reasons to perform product compliance testing at specific location, rather than at a test laboratory. A major reason is that the equipment may be physically too large for a test laboratory. The other reason is that special support equipment or infrastructure is needed to operate the equipment. For example, the electricity supply may have specific voltage or amperage requirements that cannot be accommodated in the laboratory. Other operational needs may include mechanical services such as air-handling, chemical requirements, other support equipment. Other reasons may include security issues or other special access issues relating to sensitive equipment and/or intellectual property.
-
MS561 -
MSG Equipment
Multifunctional equipment for testing EPS units. The device simulates real operation of a unit in a car, invented to diagnose pumps with electric power steering, it can be used jointly with hydraulic bench to test mechanical pumps, or separately from the bench to test electric part of a unit. The Controller tests EPS racks and columns directly in a car (if there is access to sockets) without dismounting of a unit. This method eliminates problems with wiring and other electronic units. The device has also OBD II connector for diagnostic scanner to detect errors. Besides diagnostics, the Controller contributes to more effective repair of a unit. The equipment can be placed on a table due to its small dimensions. Separate part of EPS unit can be connected to the device to analyze failures.
-
SignalCore, Inc.
SignalCore offers traditional multi-stage and single-stage RF downconverters, and Direct IQ demodulators that feature low phase noise, high dynamic range, wide bandwidth, and continuous tuning. SignalCore RF downconverters are compact and built for mechanical robustness and ruggedness. Applications include various test and measurement applications such as those in spectral monitoring, signal intelligence, ATE, and software-defined radio. All products are provided with a Graphical User Interface (GUI), driver, and API for easy programming control.
-
85052D -
Keysight Technologies
The Keysight 85052D economy mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection. Connector gauges may be ordered separately.
-
Robson Technologies, Inc.
RTI designs and manufactures DUT boards for many types of special purpose test equipment including: ESD test systems, special purpose functional testers, automated curve trace equipment, as well as standard semiconductor test equipment. All designs are performed in-house using PCB design software (Mentor PADS, CAM350) and 3D mechanical design software (Solid Edge) if required. PCB fabrication is sub-contracted to one of our long-time fabrication partners.
-
Eastern-Optx
Eastern OptX now offers System Integration for all of our equipment along with other instruments including: RF, microwave, and Optical test equipment, power conditioning, distribution, and back-up, system controllers, and data recording devices. We also offer test solution development including mechanical design, rack layout, and custom control software. Eastern-OptX will help you to design and develop your test solution and deliver a completely assembled and tested system.
-
HopeTech
High-stability internal resistance of the battery Meter.The main battery internal resistance and battery voltage. This product can simultaneously measure the resistance and voltage and to compare battery internal resistance and open-circuit voltage.The CHT3560 standard RS232C and HANDLER interface automated measurement fast and accurate judgment the battery deterioration of the situation, sorting products suitable for battery assembly line and factory inspection. Low resistance characteristics can be used to characterize the mechanical and electrical components down low current test conditions.
